Hello, Somebody who help me...

Please help me... I don't know what's wrong.

- STM32F2x7_ETH_Lwip + 3 task (I made 3 tasks)
- MDK-ARM

I sometimes got a HardFault_Handler.

Call stack + Locals (I can see below call stack when i got a hardfault_handler)
-----------------------------------------------------------------
- HardFault_Handler 0x08019892
- vPortSetInterruptMask 0x0800020A
- xPortSysTickHandler 0x0804CA06
----------------------------------------------------------------

I don' know what's wrong.

=========================================================================================
added 3 tasks
=========================================================================================
xTaskCreate(uart_task, "UART_DEBUG", configMINIMAL_STACK_SIZE, NULL, LED_TASK_PRIO+1, NULL);
xTaskCreate(uart_timer_task, "UART_TIMER", configMINIMAL_STACK_SIZE, NULL, LED_TASK_PRIO, NULL);
xTaskCreate(CDS_ITF_task, "CDS_IFT", 7168, NULL, 10, NULL);

===============================================================================================
FreeRTOSConfig.h
===============================================================================================
#define configUSE_PREEMPTION1
#define configUSE_IDLE_HOOK 0
#define configUSE_TICK_HOOK 0
#define configCPU_CLOCK_HZ ( ( unsigned long ) 120000000 )
#define configTICK_RATE_HZ ( ( portTickType ) 1000 )
#define configMAX_PRIORITIES( ( unsigned portBASE_TYPE ) 15 )//7->8
#define configMINIMAL_STACK_SIZE( ( unsigned short ) 128 )
#define configTOTAL_HEAP_SIZE( ( size_t ) ( 50*1024))//70 * 1024 ) )
#define configMAX_TASK_NAME_LEN( 16 )
#define configUSE_TRACE_FACILITY1
#define configUSE_16_BIT_TICKS0
#define configIDLE_SHOULD_YIELD1
#define configUSE_MUTEXES 1
#define configUSE_COUNTING_SEMAPHORES 1
#define configUSE_MALLOC_FAILED_HOOK 0


/* Co-routine definitions. */
#define configUSE_CO_ROUTINES 0
#define configMAX_CO_ROUTINE_PRIORITIES ( 2 )

/* Set the following definitions to 1 to include the API function, or zero
to exclude the API function. */

#define INCLUDE_vTaskPrioritySet1
#define INCLUDE_uxTaskPriorityGet1
#define INCLUDE_vTaskDelete1
#define INCLUDE_vTaskCleanUpResources 0
#define INCLUDE_vTaskSuspend0
#define INCLUDE_vTaskDelayUntil0
#define INCLUDE_vTaskDelay 1

/* This is the raw value as per the Cortex-M3 NVIC. Values can be 255
(lowest) to 0 (1?) (highest). */
#define configKERNEL_INTERRUPT_PRIORITY 255
#define configMAX_SYSCALL_INTERRUPT_PRIORITY 191 /* equivalent to 0xb0, or priority 11. */


/* This is the value being used as per the ST library which permits 16
priority values, 0 to 15. This must correspond to the
configKERNEL_INTERRUPT_PRIORITY setting. Here 15 corresponds to the lowest
NVIC value of 255. */
#define configLIBRARY_KERNEL_INTERRUPT_PRIORITY15
===============================================================================================

I don't think the code you posted can help remote diagnostic without seeing the task code.

Did you start with a working project? Can you go back to that and add back in your code bit by bit until the problem replicates?

Do you have stack overflow checking turned on.

Have you ensured all the topics on this page are covered? Especially point 3: http://www.freertos.org/FAQHelp.html

Regards.

Thanks for your advices.
I did go back to orginal working project. And then I added some code again step by step.
I think I found a problem where occur.
=======================================================================
I modified a scatter file to use an external memory.
# scatter file.
LR_IROM1 0x08000000 0x00100000 { ; load region size_region
ER_IROM1 0x08000000 0x00100000 { ; load address = execution address
*.o (RESET, +First)
*(InRoot$$Sections)
.ANY (+RO)
}
;RW_IRAM1 0x20000000 0x00020000 { ; RW data
; .ANY (+RW +ZI)
;}
RW_RAM1 0x60000000 0x00100000 { ; RW data
.ANY (+RW +ZI)
heap_2.o (+RW +ZI)
tasks.o (+RW +ZI)
}
RW_IRAM1 0x20000000 0x00020000 {
startup_stm32f2xx.o (+RW +ZI)
stm32f2xx_rcc.o (+RW +ZI)
stm32f2x7_eth.o (+RW +ZI)

}
}
==========================================================================
It was mainly cause. But I don't have any ideas to clear it.

If you have any ideas, please give me some ideas.

Regards

I added back in my code bit by bit. When I use an external ram, It always occurred.

In the beginning, it works well.
But after some minutes, I got a problem about systick handler.
Before crash the system, the system works slowly. And then the system crash...

What do I do anything else?

Please give me some ideas...




; *************************************************************
; *** Scatter-Loading Description File generated by uVision ***
; *************************************************************

LR_IROM1 0x08000000 0x00100000 { ; load region size_region
ER_IROM1 0x08000000 0x00100000 { ; load address = execution address
*.o (RESET, +First)
*(InRoot$$Sections)
.ANY (+RO)
}
RW_RAM1 0x60000000 UNINIT 0x00100000 { ; RW data
heap_2.o(+RW +ZI)
}
RW_IRAM1 0x20000000 0x00020000 {
.ANY (+RW +ZI)
}
}

-----------------------------------------------------------------------------------------
startup code
===============================================
__initial_sp
__initial_spTop EQU 0x20000400 ; stack used for SystemInit & SystemInit_ExtMemCtl
.
.
.
;__Vectors DCD __initial_sp ; Top of Stack
__Vectors DCD __initial_spTop ; Top of Stack
==========================================================================